Details

---

LEDVANCE OPTOTRONIC FIT CS G3 - OT FIT 40/220…240/1A0 CS

• OT FIT 40/220…240/1A0 CS

Product family features

• Lifetime: up to 50,000 h (temperature at max. tc) 
• Cable clamp kit for independent mounting

Product family benefits

• Higher quality of light thanks to low output ripple current
• High flexibility due to four different output currents
• Small housing for flexible luminaire designs
• High efficiency

Areas of application

• Suitable for downlights, spotlights and LED panels
• Suitable for luminaires of protection classes I and II

Electrical data

• Nominal input voltage : 220…240 V
• Mains frequency : 50/60 Hz
• Input voltage AC : 198…264 V 
• Total harmonic distortion : < 10 % 1)
• Power factor λ : 0.98 
• Efficiency in full-load : 90 % 2)
• Device power loss : 4.9 W 3)
• Protective conductor current : <0.7 mA
• Inrush current : ≤ 35 A 4)
• Max. ECG no. on circuit breaker 10 A (B) : 11
• Max. ECG no. on circuit breaker 10 A (C) : 19
• Max. ECG no. on circuit breaker 16 A (B) : 19
• Max. ECG no. on circuit breaker 16 A (C) : 31
• Max. ECG no. on circuit breaker 25 A (B) : 29
• Surge capability (L/N-Ground) : 2 kV
• Surge capability (L-N) : 1 kV
• Nominal output voltage : 25…42 V / 30...42V 5)
• U-OUT (working voltage) : 60 V
• Nominal output current : 800 / 900 / 950 / 1050 mA
• Output current tolerance : ±7.5 %
• Default output current : 1050 mA
• Output ripple current (100 Hz) : < 5 % 
• Output PSTLM : ≤1
• Output SVM : ≤0.4
• Nominal output power : 20…44.1 W
• Maximum output power : 44.1 W
• Galvanic isolation : SELV
• Galvanic isolation primary/secondary : SELV
• Current set : DipSwitch

1. At full load, 230 V, 50 Hz / see graphs
2. at 230 V, 50 Hz
3. At 230 V, Input power 49 W max.
4. twidth = 200 µs (measured at 50 % Ipeak)
5. 30 - 42V @ 1050 mA

Dimensions & weight

• Mounting hole spacing, length : 88.0 mm
• Mounting hole spacing, width : 34.0 mm
• Product weight : 110.00 g
• Cable cross-section, input side : 0.5…1.5 mm² 
• Cable cross-section, output side : 0.5…1.5 mm² 
• Wire preparation length, input side : 7…8 mm
• Wire preparation length, output side : 7…8 mm
• Length : 97.0 mm
• Width : 43.0 mm
• Height : 29.5 mm

Colors & materials

• Casing material : Plastic

Temperatures & operating conditions

• Ambient temperature range : -20…+50 °C
• Maximum temperature at tc test point : 80 °C 
• Max.housing temperature in case of fault : 110 °C
• Temperature range at storage : -20…80 °C
• Permitted rel. humidity during operation : 5…85 % 1)

1. Non-condensing

Lifespan

• ECG lifetime : 50000 h 1)

1. At maximum Tc = 80°C / 10% failure rate

Additional product data

• Predecessor EAN : 4052899435650

Capabilities

• Dimmable : No
• Overheating protection : Automatic reversible
• Overload protection : Automatic reversible
• Short-circuit protection : Automatic reversible
• No-load proof : Yes
• Intended for no-load operation : No
• Max. cable length to lamp/LED module : 2.0 m 1)
• Suitable for fixtures with prot. class : I / II
• Type of connection, input side : Push terminal
• Type of connection, output side : Push terminal
• Suitable for through-wiring : No
• Control interface : -
• Detection angle (Light sensor) : -
• Detection angle (PIR) : -
• Number of channels : 1

1. Output wires must be routed as close as possible to each other

Programming

• Programming device : DIPswitch

Certificates & standards

• Approval marks – approval : CCC / CE / RCM / ENEC 05
• Standards : Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to / IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3- / 2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
• Type of protection : IP20
• Protection class : I,II